Search

Pacemaker Headers PH5302 (extractors) | Holden HK, HG, HT | 307, 327, 350 Chev
search

Holden HK HT HG 283 307 327 350 Chev Pacemaker Headers PH5302

$1,043.51
Tax included

Holden HK HT HG 283 307 327 350 Chev 1968-1971 283, 302, 305, 307, 327, 350, 400 V8 Small Block Chev Motor Pacemaker headers (extractors). 1 5/8" [41mm] primary pipes, 2.00" [51mm] secondary pipes and 2.25" [57mm] outlets.
Click Image for larger view and more images
Best Mufflers provides expert advice and ships Australia-wide and internationally.

Quantity
In Stock

Holden HK HT HG 283 307 327 350 Chev Pacemaker Headers PH5302

SKU: PH5302 Pacemaker Headers for Holden HK HT HG 283 307 327 350 Chev. These headers use 1 5/8" [41mm] primary pipes, 2.00" [51mm] secondary pipes and 2.25" [57mm] outlets to improve exhaust flow, torque and throttle response.

Jump to: Fitment | Specifications | Warranty | FAQ

Vehicle Fitment

Make Model Years Body Series Engine Drivetrain
Holden HK / HT / HG 1968-1971 Sedan / Wagon / Ute / Van HK / HT / HG 283, 302, 305, 307, 327, 350, 400 V8 Small Block Chev Motor RWD

Fitment Notes

  • Will fit slant plug heads.
  • Fits with original engine mount spacers fitted on correct side. (RH spacer is 1 3/4"] [LH spacer is 1 1/4"]
  • Will fit turbo 350 & turbo 400 automatic
  • Will fit Powerglide automatic.
  • Will not fit with power steering
  • Will not fit with alloy raised port heads
  • Will not fit column change automatic.
  • Will fit with LH hydraulic clutch conversion.
  • Will fit factory starter motor with 10 1/2" flex plate automatic [153 tooth] Will fit factory starter motor with 13.00" flex plate manual [153 tooth] Will not fit with factory starter motor with 11.00" flex plate [168 tooth] automatic Will not fit with factory starter motor with 14.00" flex plate [168 tooth] manual
  • Protect painted surfaces and wrap headers during trial fitting
  • Clearance may vary with engine mounts, steering, and aftermarket parts
  • Will fit Turbo 400 automatic if vehicles floor has been cut for correct fitment of automatic
  • Will only fit with original engine mounting spacers or PACEMAKER spacers Part number Pemp 307
  • Note: spacers must be fitted on correct side of vehicle. (RH spacer is 1/4" higher than LH spacer)
  • Will not fit column automatic unless linkages are modified
  • PH5302 headers are designed to fit with genuine factory starter when fitting to a 153 tooth (10 1/2") flex plate (auto only) or 153 tooth (13") ring gear (manual only)
  • PH5302 headers will not fit the genuine factory starter when fitting to 168 tooth (11") flex plate (auto only) or 168 tooth (14") ring gear (manual only). Pacemaker recommends the use of an after market hi-torque starter. Please choose carefully as not all starter solenoids are in the same position.
  • Confirm the vehicle, engine, transmission and existing modifications before ordering.
  • Verify emissions, noise and vehicle registration compliance in your state or territory before installation.

Specifications

Header Details
Part number SKU: PH5302
Brand Pacemaker
Design Tri-Y Design
Primary pipes 1 5/8" [41mm]
Secondary pipes 2.00" [51mm]
Outlet 2.25" [57mm]
Finish Pacemaker Blue heat-resistant finish
Power steering No
Header gasket DSF009 header gaskets, sold separately

What's Included and Recommended With

  • PH5302 Pacemaker headers.
  • DSF009 header gaskets are available separately and are recommended for a reliable seal.
  • Ceramic coating is available as an optional upgrade. See PHC10.

Why Good Headers & Exhaust Systems Matter

A 400ci Small Block Chev V8 draws in about 11,220 L/min of air at 4,000 rpm and 85% volumetric efficiency, and expels an estimated 33,660 L/min of exhaust gas at 600°C.

Good quality headers and a correctly sized exhaust system help reduce exhaust restriction, improve exhaust scavenging, increase torque and engine performance.

Warranty & Compliance

Pacemaker headers are covered against manufacturing defects subject to Pacemaker's current warranty terms and conditions. The warranty applies to the supplied parts and does not cover labour, freight, removal, refitting or consequential costs.

Correct installation, adequate clearance, proper engine tuning and secure exhaust support are essential for warranty coverage. Vehicle modifications and exhaust requirements vary between states. The completed installation must comply with the roadworthy and emissions rules that apply where the vehicle is registered.

Frequently Asked Questions

What vehicles do PH5302 headers suit?

PH5302 suits Holden HK HT HG 283 307 327 350 Chev fitted with the 283, 302, 305, 307, 327, 350, 400 V8 Small Block Chev Motor. Confirm your vehicle, engine, transmission and existing modifications before ordering.

Are PH5302 headers Tri-Y?

Yes. Pacemaker specifies PH5302 as a Tri-Y design.

What size are the PH5302 header pipes?

Pacemaker specifies 1 5/8" [41mm] primary pipes, 2.00" [51mm] secondary pipes and 2.25" [57mm] outlets.

Which exhaust gasket is recommended?

The recommended exhaust manifold/header gasket is DSF009, available separately.

Can you arrange for the PH5302 headers to be ceramic coated?

Yes. If you require ceramic coating for these headers see PHC10 for pricing details.

Can I pick up from the store?

Yes. Pick up is available but must be pre-arranged before collection. Contact Best Mufflers to confirm availability before travelling.

How much is freight?

Freight varies depending on your delivery location and where stock is available. Please contact us for freight charges before ordering. Where possible, we can arrange dispatch from the nearest available product location to help reduce freight costs and delivery times.

Do you ship to the USA?

Yes. Best Mufflers regularly ships exhaust systems and exhaust parts to customers throughout the United States.

Please note that import duties, tariffs, taxes, and customs clearance fees are not included in the product or shipping price. Once your order is processed and the applicable charges are calculated, we will send you a secure payment link to finalise the import duties and tariff charges before dispatch.

Customer Support

For phone orders, advice, or part enquiries - contact us:

📞 Call Now: +61 2 9547 3511 ✉️ Email Us

🇦🇺 Best Mufflers
87A Planthurst Road, Carlton NSW 2218, Australia
Exhaust Systems Since 1983
Workshop hours: Mon-Fri 8:00am-5:00pm (By Appointment Only) | Phone and email enquiries welcome 24 hours

PH5302


You might also like