Search

Exhaust Header Bolts 3/8" UNC x 25mm Zinc Plated – BOL3-10
search

Exhaust Header Bolts 3/8" UNC x 25mm – Ford Chev Holden Edelbrock AFR – BOL3-10

$1.69
Tax included

Exhaust Header Bolts 3/8" UNC x 25mm Zinc Plated – BOL3-10

BOL3-10 exhaust header bolts feature a 3/8" UNC thread, 25mm (1") length and 3/8" hex head. Zinc-plated for corrosion resistance, these bolts are suitable for securing exhaust headers and extractors to compatible cylinder heads.

Commonly used on selected early Ford, Chevrolet and Holden V8 engines, including compatible factory cylinder heads and aftermarket Edelbrock and AFR heads. Always confirm thread size, bolt length and clearance before ordering.

Minimum Order Quantity: 12 bolts.

Click the image to view a larger photo.

Best Mufflers provides expert advice and fast shipping Australia-wide.

Quantity
In Stock

The minimum purchase order quantity for the product is 12.

Exhaust Header Bolts 3/8" UNC x 25mm Zinc Plated – BOL3-10

BOL3-10 exhaust header bolts are designed for securing exhaust headers and extractors to cylinder heads using 3/8" UNC threaded mounting holes. Featuring a 25mm (1") length, 3/8" hex head and zinc-plated finish, these bolts are suitable for factory and aftermarket cylinder head applications.

Key Features

  • 3/8" UNC coarse thread
  • 25mm (1") bolt length
  • 3/8" hex head for restricted header mounting areas
  • Zinc-plated finish for corrosion resistance
  • Suitable for compatible exhaust header and extractor installations
  • Minimum order quantity of 12 bolts

Construction

  • Material: Steel
  • Finish: Zinc plated
  • Thread: 3/8" UNC
  • Head Size: 3/8" hex
  • Length: 25mm (1")

Product Specifications

  • SKU: BOL3-10
  • Product: Exhaust header mounting bolt
  • Thread Diameter: 3/8" (9.525mm)
  • Thread Type: UNC coarse thread
  • Thread Pitch: 16 TPI
  • Bolt Length: 25mm (1")
  • Hex Head Size: 3/8"
  • Finish: Zinc plated
  • Minimum Order Quantity: 12 bolts

Additional Options

Vehicle & Engine Applications

  • Selected early Ford engines with 3/8" UNC exhaust header mounting threads
  • Selected Chevrolet engines with compatible exhaust header mounting threads
  • Selected Holden engines with compatible exhaust header mounting threads
  • Compatible Edelbrock aftermarket cylinder heads
  • Compatible AFR aftermarket cylinder heads

Fitment Notes

  • FOR CYLINDER HEADS USING 3/8" UNC EXHAUST HEADER MOUNTING THREADS
  • Confirm thread diameter, pitch and bolt length before ordering
  • Check bolt head clearance around header primary pipes and flanges
  • Not all Ford, Chevrolet, Holden, Edelbrock or AFR cylinder heads use the same mounting hardware
  • Ensure adequate thread engagement without the bolt bottoming out in the cylinder head
  • Check that the bolt length is suitable for the combined header flange and gasket thickness

What's Included

  • Exhaust Header Bolts SKU: BOL3-10
  • Minimum purchase quantity: 12 bolts

Recommended With

  • Exhaust header gaskets matched to the cylinder head application
  • Compatible exhaust headers or extractors
  • Suitable high-temperature anti-seize compound, where recommended by the cylinder head or fastener manufacturer

Installation Tips

  • Check that the cylinder head threads are clean and undamaged before installation
  • Confirm the correct bolt length and thread engagement
  • Start all bolts by hand to prevent cross-threading
  • Use a suitable high-temperature anti-seize compound only where permitted by the manufacturer
  • Tighten bolts to the cylinder head or header manufacturer's recommended torque specification
  • Inspect header flange sealing and fastener tightness after initial heat cycles, where recommended

Warranty & Compliance

Replacement exhaust header mounting hardware designed for compatible automotive applications. Correct thread selection, installation and tightening procedures are essential. Warranty applies to the supplied parts only, subject to applicable Australian Consumer Law rights.

Frequently Asked Questions

What thread size are BOL3-10 header bolts?
These bolts feature a 3/8" UNC coarse thread with 16 threads per inch.

How long are the bolts?
The specified bolt length is 25mm (approximately 1").

What size is the bolt head?
The hex head is listed as 3/8", allowing access in some restricted header mounting areas.

Will these bolts suit Edelbrock and AFR cylinder heads?
They suit selected Edelbrock and AFR cylinder heads using compatible 3/8" UNC exhaust mounting threads. Check the cylinder head manufacturer's specifications before ordering.

Are the bolts zinc plated?
Yes. BOL3-10 bolts have a zinc-plated finish.

What is the minimum order quantity?
The minimum order quantity is 12 bolts.

Can I collect my order?
Yes. Pickup must be pre-arranged. Please contact us before ordering to confirm availability and arrange collection.

How much is freight?
Freight varies depending on delivery location and stock availability. Please contact us before ordering for freight charges.

Do you ship to the USA?
Yes. Best Mufflers regularly ships exhaust systems and exhaust parts to customers throughout the United States. Please note that import duties, tariffs, taxes, and customs clearance fees are not included in the product or shipping price. Once your order is processed and the applicable charges are calculated, we will send you a secure payment link to finalise the import duties and tariff charges before dispatch.

Customer Support

For phone orders, advice, or part enquiries – contact us:

📞 Call Now: +61 2 9547 3511 ✉️ Email Us

🇦🇺 Best Mufflers
87A Planthurst Road, Carlton NSW 2218, Australia
Exhaust Systems Since 1983
Workshop hours: Mon–Fri 8:00am–5:00pm (By Appointment Only) | Phone and email enquiries welcome 24 hours

BOL3-10


You might also like