Search

Holden HQ HJ HX HZ WB 5.0 & 5.7 with EFI Heads Pacemaker Headers / Extractors PN# PH5275
search

Holden HQ HJ HX HZ WB 5.0 EFI V8 Pacemaker Competition Headers PH5275

$1,029.84
Tax included

Holden HQ HJ HX HZ WB 5.0 EFI V8 1971-1985 5.0L EFI V8 (304 engine conversion from VN, VP, VR, VS or VT Series 1), or EFI heads on an original 253 or 308 Holden V8 block Pacemaker competition headers (extractors). 1.75" [44mm] primary pipes, 2.00" [51mm] secondary pipes and 3.00" [76mm] outlets.
Click Image for larger view and more images
Best Mufflers provides expert advice and ships Australia-wide and internationally.

Quantity
In Stock

Holden HQ HJ HX HZ WB 5.0 EFI V8 Pacemaker Competition Headers PH5275

SKU: PH5275 Pacemaker Headers for Holden HQ HJ HX HZ WB 5.0 EFI V8. These headers use 1.75" [44mm] primary pipes, 2.00" [51mm] secondary pipes and 3.00" [76mm] outlets to improve exhaust flow, torque and throttle response.

Jump to: Fitment | Specifications | Warranty | FAQ

Vehicle Fitment

MakeModelYearsBodySeriesEngineDrivetrain
HoldenKingswood / Statesman / Ute / Van1971-1985Sedan / Wagon / Ute / VanHQ / HJ / HX / HZ / WB5.0L EFI V8 (304 engine conversion from VN, VP, VR, VS or VT Series 1), or EFI heads on an original 253 or 308 Holden V8 blockRWD

Fitment Notes

  • Will fit: Australian four speed with cable clutch, Commodore VN-VS five speed, Toyota Supra five speed with Hatfield bellhousing, Holden Trimatic, Holden Turbo 350 and Turbo 400
  • Will fit Commodore four speed automatic Turbo 700 with Hatfield rear cross member, using Turbo 700 gearbox mounts and 308 engine mounts
  • Will fit with High Energy sump HE2101
  • Will fit with HQ type mechanical clutch
  • Suitable for 5.7L stroked or supercharged engines
  • Suitable for 5.7 Litre stroked or super charged motor
  • Holden Turbo 400
  • Will fit with High Energy Sump HE2101 Part No.
  • Hatfield rear cross member using Turbo 700 gear box
  • Confirm the vehicle, engine, transmission and existing modifications before ordering.
  • Verify emissions, noise and vehicle registration compliance in your state or territory before installation.

Specifications

Header Details
Part number SKU: PH5275
Brand Pacemaker
Design Tri-Y Design
Primary pipes 1.75" [44mm]
Secondary pipes 2.00" [51mm]
Outlet 3.00" [76mm]
Finish Pacemaker Blue heat-resistant finish
Power steering Yes
Air conditioning Yes
Oxygen sensor fittings Incorporated into the headers
Header gasket DSF063 header gaskets, sold separately

What's Included and Recommended With

  • PH5275 Pacemaker headers.
  • Oxygen sensor fittings incorporated into the headers.
  • DSF063 header gaskets are available separately and are recommended for a reliable seal.
  • Ceramic coating is available as an optional upgrade. See PHC10.

Why Good Headers & Exhaust Systems Matter

A 308ci EFI V8 draws in about 8,500 L/min of air at 4,000 rpm and 85% volumetric efficiency, and expels an estimated 25,500 L/min of exhaust gas at 600°C.

Good quality headers and a correctly sized exhaust system help reduce exhaust restriction, improve exhaust scavenging, increase torque and engine performance.

Warranty & Compliance

Pacemaker headers are covered against manufacturing defects subject to Pacemaker's current warranty terms and conditions. The warranty applies to the supplied parts and does not cover labour, freight, removal, refitting or consequential costs.

Correct installation, adequate clearance, proper engine tuning and secure exhaust support are essential for warranty coverage. Vehicle modifications and exhaust requirements vary between states. The completed installation must comply with the roadworthy and emissions rules that apply where the vehicle is registered.

Frequently Asked Questions

What vehicles do PH5275 headers suit?

PH5275 suits Holden HQ HJ HX HZ WB 5.0 EFI V8 fitted with the 5.0L EFI V8 (304 engine conversion from VN, VP, VR, VS or VT Series 1), or EFI heads on an original 253 or 308 Holden V8 block. Confirm your vehicle, engine, transmission and existing modifications before ordering.

Are PH5275 headers Tri-Y?

Yes. Pacemaker specifies PH5275 as a Tri-Y design.

What size are the PH5275 header pipes?

Pacemaker specifies 1.75" [44mm] primary pipes, 2.00" [51mm] secondary pipes and 3.00" [76mm] outlets.

Which exhaust gasket is recommended?

The recommended exhaust manifold/header gasket is DSF063, available separately.

Can you arrange for the PH5275 headers to be ceramic coated?

Yes. If you require ceramic coating for these headers see PHC10 for pricing details.

Can I pick up from the store?

Yes. Pick up is available but must be pre-arranged before collection. Contact Best Mufflers to confirm availability before travelling.

How much is freight?

Freight varies depending on your delivery location and where stock is available. Please contact us for freight charges before ordering. Where possible, we can arrange dispatch from the nearest available product location to help reduce freight costs and delivery times.

Do you ship to the USA?

Yes. Best Mufflers regularly ships exhaust systems and exhaust parts to customers throughout the United States.

Please note that import duties, tariffs, taxes, and customs clearance fees are not included in the product or shipping price. Once your order is processed and the applicable charges are calculated, we will send you a secure payment link to finalise the import duties and tariff charges before dispatch.

Customer Support

For phone orders, advice, or part enquiries - contact us:

📞 Call Now: +61 2 9547 3511 ✉️ Email Us

🇦🇺 Best Mufflers
87A Planthurst Road, Carlton NSW 2218, Australia
Exhaust Systems Since 1983
Workshop hours: Mon-Fri 8:00am-5:00pm (By Appointment Only) | Phone and email enquiries welcome 24 hours

PH5275


You might also like