Search

Pacemaker Headers PH5000FA (extractors) for Holden Commodore VS Series 3 Ute, 5.0L EFI with Getrag 5 speed Manual (photo 1 of 4)
search

Holden Commodore VS Series 3 Ute 5.0L V8 Pacemaker Headers PH5000FA

$1,155.00
Tax included

Holden Commodore VS Series III Ute 5.0L V8 Pacemaker Headers PH5000FA (extractors) designed for models with Getrag 5 speed manual transmission 1998-2001. These headers have 1 5/8" [41mm] primary pipes, 1 7/8" [48mm] secondary pipes and 2.50" [63mm] outlet to bolt to the factory catalytic converter.

Click Image for larger view and more images
Best Mufflers provides expert advice and ships Australia-wide.

Quantity
In Stock

Holden Commodore VS Series 3 Ute 5.0L V8 Manual Pacemaker Headers PH5000FA

PH5000M Pacemaker Headers for Holden Commodore VS Series 3 Ute 5.0L V8 5 Speed Manual transmission. These headers use 1 5/8" [41mm] primary pipes, 1 7/8" [48mm] secondary pipes and 2.50" [63mm] outlet to bolt to the catalytic converter to improve exhaust flow, torque and throttle response.

Jump to: Fitment | Specifications | Warranty | FAQ

Vehicle Fitment

Make Model Years Body Series Engine Drivetrain
Holden Commodore 6/1998-12/2000 Ute VS Series III Ute 5 Litre E.F.I. V8 RWD

Fitment Notes

  • Will not fit with six speed manual. see PH5002
  • Will Not fit VS Series 3 Ute with Getrag 5 speed see PH5000A
  • Will not fit with full circle bell housing
  • Protect painted surfaces and wrap headers during trial fitting
  • Clearance may vary with engine mounts, steering, and aftermarket parts
  • Will NOT fit with Variable Ratio Power Steering
  • Will fit both Bosch starter motors
  • *Not six speed manual, use part number PH5002
  • *Not Series III VS ute with Getrag 5 speed manual, use part number PH5000A
  • Product Specs
  • Confirm the vehicle, engine, transmission and existing modifications before ordering.
  • Verify emissions, noise and vehicle registration compliance in your state or territory before installation.

Specifications

Header Details
Part number SKU: PH5000FA [PH5000A]
Brand Pacemaker
Design Tri-Y Design
Primary pipes 1 5/8" [41mm]
Secondary pipes 1 7/8" [48mm]
Outlet 2.50" [63mm]
Finish Pacemaker Blue heat-resistant finish
Power steering Yes
Air conditioning Yes
Oxygen sensor fittings Incorporated into the headers
Header gasket DSF063 header gaskets, sold separately

What's Included and Recommended With

  • PH5000FA [PH5000A] Pacemaker headers.
  • Oxygen sensor fittings incorporated into the headers.
  • DSF063 header gaskets are available separately and are recommended for a reliable seal.
  • Ceramic coating is available as an optional upgrade. See "PHC10" for left/right header and "PHC90" base pipe

Why Good Headers & Exhaust Systems Matter

A 5.0L V8 draws in about 8,500 L/min of air at 4,000 rpm and 85% volumetric efficiency, and expels an estimated 25,500 L/min of exhaust gas at 600°C.

Good quality headers and a correctly sized exhaust system help reduce exhaust restriction, improve exhaust scavenging, increase torque and engine performance.

Warranty & Compliance

Pacemaker headers are covered against manufacturing defects subject to Pacemaker's current warranty terms and conditions. The warranty applies to the supplied parts and does not cover labour, freight, removal, refitting or consequential costs.

Correct installation, adequate clearance, proper engine tuning and secure exhaust support are essential for warranty coverage. Vehicle modifications and exhaust requirements vary between states. The completed installation must comply with the roadworthy and emissions rules that apply where the vehicle is registered.

Frequently Asked Questions

What vehicles do PH5000FA headers suit?

PH5000FA suits Holden Commodore VS Series 3 Ute 5.0 V8 Manual fitted with the 5 Litre E.F.I. V8 and Getrag 5 speed manual. Confirm your vehicle, engine, transmission and existing modifications before ordering.

Are PH5000FA headers Tri-Y?

Yes.  The PH500FA are Tri-Y design.

What size are the PH5000FA header pipes?

Pacemaker specifies 1 5/8" [41mm] primary pipes, 1 7/8" [48mm] secondary pipes and 2.50" [63mm] outlet.

Which exhaust gasket is recommended?

The recommended exhaust manifold/header gasket is DSF063, available separately.

Can you arrange for the PH5000FA headers to be ceramic coated?

Yes. If you require ceramic coating for these headers see product code "PHC10" for left / right header and "PHC90" for base pipe for pricing details.

Can I pick up from the store?

Yes. Pick up is available but must be pre-arranged before collection. Contact Best Mufflers to confirm availability before travelling.

How much is freight?

Freight varies depending on your delivery location and where stock is available. Please contact us for freight charges before ordering. Where possible, we can arrange dispatch from the nearest available product location to help reduce freight costs and delivery times.

Do you ship to the USA?

Yes. Best Mufflers regularly ships exhaust systems and exhaust parts to customers throughout the United States.

Please note that import duties, tariffs, taxes, and customs clearance fees are not included in the product or shipping price. Once your order is processed and the applicable charges are calculated, we will send you a secure payment link to finalise the import duties and tariff charges before dispatch.

Customer Support

For phone orders, advice, or part enquiries - contact us:

📞 Call Now: +61 2 9547 3511 ✉️ Email Us

🇦🇺 Best Mufflers
87A Planthurst Road, Carlton NSW 2218, Australia
Exhaust Systems Since 1983
Workshop hours: Mon-Fri 8:00am-5:00pm (By Appointment Only) | Phone and email enquiries welcome 24 hours

PH5000FA


You might also like