Holden Commodore VS Wagon 04/1995-08/1997 3.8L ECOTEC V6 Rear Muffler Assembly BM4354A

BM4354A rear muffler assembly is an Australian-made direct-fit replacement exhaust component designed for Holden Commodore VS Wagons manufactured from 04/1995 to 08/1997 fitted with the naturally aspirated 3.8L ECOTEC V6 petrol engine.

This assembly replaces the original rear muffler section of the exhaust system and is designed for factory-style fitment, making it suitable for replacement of a rusted, damaged or leaking original rear muffler assembly.

Please check availability and current lead time before ordering.

Key Features

• Direct-fit replacement rear muffler assembly
• Designed for Holden Commodore VS Wagon 3.8L ECOTEC V6
• Suits VS Series I and Series II within the listed production range
• Factory-style replacement exhaust component
• Uses the original-style exhaust mounting locations
• Australian Made
• Quality replacement exhaust component
• Australia-wide delivery available

Construction

• Factory-style rear muffler assembly
• Complete rear muffler and connecting pipe section
• Designed for direct replacement of the original rear exhaust section
• Australian made

Additional Options

• GMG093: Exhaust gasket available separately
• GMR007: Exhaust mounting rubber available separately
• Other replacement exhaust components for Holden Commodore VS models are available separately

Vehicle Fitment

• Make: Holden
• Model: Commodore
• Series: VS Series I / VS Series II
• Body: Wagon
• Production Range: 04/1995-08/1997
• Engine: 3.8L ECOTEC V6 petrol
• Capacity: 3791cc
• Power: 147kW
• Induction: Naturally Aspirated
• Drive: Rear Wheel Drive

The VS Commodore was introduced in April 1995 with Holden's revised 3.8L ECOTEC V6 producing 147kW. VS sedan and wagon production continued through to August 1997, when the VT generation replaced it.

Fitment Notes

• Wagon application only
• Suits naturally aspirated 3.8L ECOTEC V6 applications
• Suits applicable VS Series I and Series II wagons
• Direct-fit replacement for the original rear muffler assembly
• Inspect the exhaust gasket during installation and replace where required
• Inspect the exhaust mounting rubber and replace if cracked, stretched or deteriorated
• Lubricate mounting rubbers and exhaust fasteners with penetrating lubricant before removal to make removal and installation easier
• Please check availability and current lead time before ordering.

What’s Included

• 1 x BM4354A rear muffler assembly

Recommended With

• GMG093 – exhaust gasket
• GMR007 – exhaust mounting rubber

Installation Tips

Before removing the original exhaust, apply penetrating lubricant to the exhaust fasteners. Lubricating the exhaust mounting rubbers will also make removal and installation easier.

Inspect the GMG093 exhaust gasket and GMR007 mounting rubber during installation. Replace deteriorated components to help prevent exhaust leaks, excessive exhaust movement and premature failure.

After installation, check the rear muffler and pipework for adequate clearance from the vehicle body, suspension, fuel tank and surrounding components. Start the engine and inspect all exhaust connections for leaks.

Warranty & Compliance

BM4354A is intended as a direct-fit replacement exhaust component for the listed Holden Commodore VS Wagon application. Correct vehicle identification and installation are important for proper fitment and service life.

FAQ

What vehicle does BM4354A fit?
BM4354A suits Holden Commodore VS Wagons from 04/1995 to 08/1997 fitted with the naturally aspirated 3.8L ECOTEC V6 petrol engine.

Does BM4354A fit both VS Series I and Series II Wagons?
Yes. BM4354A suits applicable VS Series I and Series II 3.8L ECOTEC V6 Wagons within the listed production range.

Does BM4354A fit earlier VN, VP and VR Commodore Wagons?
BM4354 is also listed for selected VN, VP and VR 3.8L V6 Wagons from 11/1990 through to the introduction of the VS in 04/1995.

Does BM4354A fit a VS Commodore Sedan?
No. This listing is for the Wagon application. Sedan and wagon rear exhaust systems differ.

Is BM4354A a direct-fit replacement?
Yes. BM4354 is designed as a direct-fit replacement rear muffler assembly for the listed wagon application.

Is BM4354A Australian made?
Yes. BM4354A is Australian made.

Is the exhaust gasket included?
GMG093 is available separately. Inspect the existing gasket during installation and replace it where required.

Which exhaust mounting rubber is used?
GMR007 is listed for this application and is available separately.

Can I pick up from the store?
Yes. Pick up is available but must be pre-arranged before collection.

How much is freight?
Freight varies depending on your delivery location and where stock is available. Please contact us for freight charges before ordering. Where possible, we can arrange dispatch from the nearest available product location to help reduce freight costs and delivery times.

Do you ship to the USA?
Yes. Best Mufflers regularly ships exhaust systems and exhaust parts to customers throughout the United States.

Please note that import duties, tariffs, taxes, and customs clearance fees are not included in the product or shipping price. Once your order is processed and the applicable charges are calculated, we will send you a secure payment link to finalise the import duties and tariff charges before dispatch.

Customer Support

For phone orders, advice, or part enquiries – contact us: