Suzuki Swift GTI 1989-1999 1.3L G13B DOHC Wildcat Exhaust Headers WILD010

Wildcat WILD010 exhaust headers (extractors) are designed for selected Suzuki Swift GTI SF13 / SF413 models from 1989–1999 fitted with the 1.3L G13B DOHC 16-valve petrol engine.

WILD010 uses 38mm primary pipes, 45mm secondary pipes and a 51mm outlet to improve exhaust gas flow and scavenging while maintaining good exhaust velocity, helping improve torque, throttle response and usable engine performance.

WILD010 is listed as a direct-fit application and includes an oxygen sensor provision. It is also listed for selected Suzuki Cultus GTI and Holden Barina GTI applications fitted with the compatible G13B engine.

Please check availability and current lead time before ordering.

Key Features

• Designed for selected Suzuki Swift GTI SF13 / SF413 applications
• Suits the 1.3L G13B DOHC 16-valve petrol engine
• Also listed for selected Suzuki Cultus GTI and Holden Barina GTI applications
• 38mm (1.50") primary pipes
• 45mm (approximately 1.75") secondary pipes
• 51mm (2.00") outlet
• Direct-fit application
• Oxygen sensor provision
• Designed to improve exhaust flow, torque, throttle response and engine performance

Construction

• Australian-made Wildcat performance headers
• Quality mild steel construction
• Strong welded construction for durability
• Formed pipework designed for efficient exhaust gas flow
• Heat-resistant painted finish rated to approximately 600°C

Additional Options

• RBG010 / DSF764C: Exhaust manifold/header gasket available separately
• Replacement manifold studs and nuts where required
• High-temperature exhaust gasket sealant where appropriate
• Performance exhaust system where further exhaust flow improvement is required

Vehicle Fitment

• Make: Suzuki
• Model: Swift GTI
• Series: SF13 / SF413 – selected applications
• Year Range: 1989–1999
• Engine: G13B
• Engine Capacity: 1.3L
• Engine Type: DOHC 16-valve petrol
• Additional Applications: Selected Suzuki Cultus GTI and Holden Barina GTI models fitted with the compatible G13B engine

Fitment Notes

• Designed for selected Suzuki Swift GTI SF13 / SF413 models fitted with the 1.3L G13B DOHC 16-valve engine
• Also listed for selected Suzuki Cultus GTI and Holden Barina GTI applications
• WILD010 is listed as a direct-fit application
• Header includes an oxygen sensor provision
• Recommended exhaust manifold/header gasket: RBG010 / DSF764C
• Engine conversions, replacement engines, modified engine mounts or non-standard exhaust systems may affect fitment
• Check the existing engine and exhaust configuration before ordering if the vehicle has been modified
• Please check availability and current lead time before ordering.

What’s Included

• 1 x Set Wildcat WILD010 exhaust headers / extractors
• Oxygen sensor provision
• Outlet connection components as supplied

Recommended With

• RBG010 / DSF764C exhaust manifold/header gasket
• Replacement manifold studs and nuts where existing hardware is worn or corroded
• High-temperature exhaust gasket sealant where appropriate
• Quality performance exhaust system where further exhaust flow improvement is required

Why Good Headers & Exhaust Systems Matter

At 4,000 rpm, the 1.3L G13B DOHC 16-valve engine theoretically draws in approximately 2,600 litres of intake air per minute and can expel around 7,800 litres of hot exhaust gas per minute at approximately 600°C.

The high-revving DOHC 16-valve G13B particularly benefits from an exhaust system capable of maintaining efficient gas flow as engine speed increases. A well-designed header and exhaust system helps reduce restriction and improve exhaust scavenging, torque, throttle response and engine performance.

Installation Tips

• Apply penetrating lubricant such as WD-40 or similar to the manifold studs, nuts and exhaust fasteners before removal
• Remove all traces of the old manifold gasket before installing the headers
• Inspect the cylinder-head sealing surface, manifold studs and threads before installation
• Fit a new RBG010 / DSF764C exhaust manifold/header gasket
• Trial-fit the headers before fully tightening the mounting hardware
• Check clearance around the engine mounts, steering, transmission, starter motor and surrounding components
• Confirm correct oxygen sensor installation and wiring clearance
• Protect the painted header surfaces during trial fitting and installation
• Check all exhaust connections for leaks after installation
• Inspect and re-tighten the header mounting hardware after the initial heat cycles

Warranty & Compliance

Wildcat headers are covered by the applicable 2-year manufacturer's warranty subject to standard warranty terms and conditions.

Installation must retain the catalytic converter, oxygen sensor and any other emissions-control equipment required for the vehicle. Exhaust and emissions requirements vary between Australian states and territories, and the completed installation must comply with the regulations applicable in your state or territory.

FAQ

Which Suzuki Swift does WILD010 suit?
WILD010 is designed for selected Suzuki Swift GTI SF13 / SF413 models from 1989–1999 fitted with the 1.3L G13B DOHC 16-valve petrol engine.

Does WILD010 suit the G13BA engine?
No. This listing is specifically for the G13B DOHC 16-valve GTI engine. The G13BA is a different engine application.

Will WILD010 fit a Suzuki Cultus GTI?
Yes. WILD010 is also listed for selected Suzuki Cultus GTI applications fitted with the compatible G13B engine.

Will WILD010 fit a Holden Barina GTI?
Yes. WILD010 is also listed for selected Holden Barina GTI applications fitted with the compatible G13B engine.

Are WILD010 headers direct fit?
Yes. WILD010 is listed as a direct-fit application for the specified compatible vehicles.

Does WILD010 have an oxygen sensor fitting?
Yes. WILD010 includes an oxygen sensor provision for the applicable installation.

What size are the WILD010 header pipes?
WILD010 uses 38mm primary pipes, 45mm secondary pipes and a 51mm outlet.

Which gasket does WILD010 use?
The recommended exhaust manifold/header gasket is RBG010 / DSF764C, available separately.

What finish is used on WILD010?
The headers have a heat-resistant painted finish rated to approximately 600°C.

Are WILD010 headers Australian made?
Yes. Wildcat WILD010 headers are manufactured in Australia.

Can I pick up from the store?
Yes. Pick up is available but must be pre-arranged before collection.

How much is freight?
Freight varies depending on your delivery location and where stock is available. Please contact us for freight charges before ordering. Where possible, we can arrange dispatch from the nearest available product location to help reduce freight costs and delivery times.

Do you ship to the USA?
Yes. Best Mufflers regularly ships exhaust systems and exhaust parts to customers throughout the United States.

Please note that import duties, tariffs, taxes, and customs clearance fees are not included in the product or shipping price. Once your order is processed and the applicable charges are calculated, we will send you a secure payment link to finalise the import duties and tariff charges before dispatch.

Customer Support

For phone orders, fitment advice or product enquiries, contact Best Mufflers:

Call Now: +61 2 9547 3511 Email Us

Best Mufflers
87A Planthurst Road, Carlton NSW 2218, Australia
Monday–Friday 8:00am–5:00pm by appointment
Exhaust Systems Since 1983